germadev.blogg.se - Descargar mac os x tiger 10.4

Descargar mac os x tiger 10.4 install#

If you also have a non-US-keyboard you may need to search for the keys to press to get what you need. And the last part puts it all into the “compatible” property. The encode+ command connects the second/thind/… string with the preceeding string.

“ Power Macintosh“ encode-string encode+.

It is easier to understand if the whole command is logically devided: The same goes for the property “compatible”, but the strings have to be connected with encode+ – which again follows the second/third/… string. So we set the string “PowerBook2,2” to be the new value of porperty “model”.

Thereafter follows another string: “ model“, followed by what to do with it: property. (Like calculating with a HP-28.) So “ PowerBook2,2″ is the string, and encode-string is what to do with it.

It is based on FORTH, a programming language, where the actual command what to do with a value follows that value. Also, it may be hard to understand the structure of Open Firmware commands. So “ PowerBook2,2″ is correct, but „PowerBook2,2“ would be incorrect and result in an error. Very important is to have each string starting with a white space after the double-quotes. The hard part really is to get the commands down correctly. This will set “compatible” to “PowerBook2,2↵MacRISC↵MacRISC2↵Power Macintosh”

“ PowerBook2,2″ encode-string “ MacRISC“ encode-string encode+ “ MacRISC2″ encode-string encode+ “ Power Macintosh“ encode-string encode+ “ compatible“ property.

“ PowerBook2,2″ encode-string “ model“ property.

You will see a list of properties displayed, two of them are “model” and “compatible” – both have to be changed In order to do what I did, type in the following at the Open Firmware prompt: So I went with PowerBook2,2, which is the 2000-model of this iBook. I decided to alter the model to report PowerMac1,1, same as my Power Mac. I rebooted and went into Open Firmware (holding Command + Option (Alt) + O + F at the chime until seeing the Open Firmware prompt). After booting it I am greeted with an alert: „Your computer is not compatible with Mac OS X 10.4.” My Tiger DVD is the one labeled as “CPU Drop In DVD”. The only difference between the original ’99 models and the 2000 models is more internal memory (64 MB instead of 32 MB), a DVD drive instead of a CD drive and FireWire-400 for the later ones.

Descargar mac os x tiger 10.4 install#

I also found out that the 2000-models of the Clamshell feature FireWire and can happily install and run Tiger. Since it was easy to install Tiger on my Power Mac G3 B&W I thought that it must be possible to install it without third-party stuff on the Clamshell as well. I gave it some thought and went along with my own Open Firmware hack, which is really easy to accomplish. So I looked for a solution and found that XPostFacto would let me install Tiger. Lukily with the upgraded DVD drive I can use the installation media directly. For the same reason, installing Tiger using target disk mode is not an option. I wanted to get Mac OS X 10.4 “Tiger” on it, but due to the lack of FireWire the PowerBook2,1 is not supported by Tiger. He gave it to me with a fresh installation of Mac OS X 10.3 “Panther”. He also replaced the original CD drive with a DVD drive, as I understand it out of necessity, because the original CD drive broke. He also managed to replace the original hard disk drive with a 120 GB drive, so I don’t have to worry about disk space limitation. My friend, who had used it for several years and replaced it a few years ago with an Intel-based MacBook, had its main memory maxed-out so it features 544 MB memory: 32 MB internal + 512 MB from the expansion slot. The hardware performance is essentially the same as I am used to from my Power Mac G3/350 Blue & White. I just got an original iBook G3/300 (sometimes also referred to as “Clamshell”) from a friend and I have to say that I do like it very much.